|
Flash TK-Jr
The TK-Jr model is the smallest unit in the Takagi line-up. The TK-Jr is perfect
for light residential (i.e. small apartment units) and radiant heating applications.
Released in 2003, the TK-Jr. is the smallest water heater in the Takagi tankless line. But this small, but powerful unit - with gas inputs up to 140,000 BTU per hour - can meet all the hot-water needs of a small American home or apartment with one or two bathrooms, as well as smaller commercial applications. Designed to virtually do anything a 40-gallon tank-type water heater can do and more, the compact, wall mounted TK-Jr. can support hydronic baseboard or radiant floor heating applications, as well as provide domestic hot water to plumbing fixtures and appliances. The TK-Jr. has an efficiency rating of 81%, using natural gas, and 83% with propane. At an average (rise in temperature) of 60°F in warmer areas - where the winter ground water is 60°F and with the output set at 120°F - the unit will provide 3.8 GPM, or 228 GPH. In colder areas where the input temperature may be 40°F or less you can expect a flow rate of about 2.7 GPM or 162 GPH.
Cost-efficient and environmentally friendly, the TK-Jr. can be converted into a direct-vent unit by using the optional TV09 conversion kit for installation in a garage, a utility closet or any confined space in which makeup air may be limited. Please refer to "Accessories" for more information on venting options.
Using the average of 60°F input water cited above, the TK-Jr. can provide enough hot water for one shower and a lavatory basin at a time; or one low-flow shower (2.5 GPM or less) and an appliance, such as a dishwasher or washing machine, at the same time. For much colder input temperatures, such as 40°F or lower, this unit can provide endless hot water for consecutive uses; that is, running only one major fixture at a time. Please refer to the flow charts for specific rates.
The four preset temperatures on the unit are: 113°F, 122°F, 140°F, and 182°F. To achieve any temperatures other than those presets, your client will require the TK-RE20 temperature controller.
For Energy Star Certifications please follow Specification Sheets and Literature that is dated 2009 ONLY. As of March 27, 2009, ONLY the TK-3 & TK-Jr Liquid Propane model qualifies as an Energy Star unit.
|
 |
 |
|
Prices
subject to change without notice. To place your order online,
enter the quantity and press "Add to Order". |
 |
|
Takagi Flash Water Heater T-KJr. NAT Gas |
| Natural
Gas |
|
Price: $695.00 |
Free Shipping: $0.00 |
Total:
$695.00 |
|
| |
|
Takagi Flash Water Heater T-KJr. LP |
| Propane
Gas |
|
Price: $695.00 |
Free Shipping: $0.00 |
Total:$695.00 |
|
|
|
|
| TK-TVO1 Wall Ventilation Terminator |
|
This terminator can be used where a T-KJR is going to be vented out through a wall. This is a CSA tested Takagi component. Connect the Category III stainless steel vent pipe from the top of the unit to the backside of this terminator to exhaust flue gases through the wall without a thimble. Install this vent terminator in accordance with Takagi's installation instructions and any applicable codes. |
 |
|
Price:
$109.00 |
Shipping:
$12.00 |
Total:
$121.00 |
|
|
| |
| TK-TV04
Ventilator Cap |
|
The TK-TV04 Vent Cap is for outdoor installation with the T-KJr. water heater. The cap is installed on the top of the unit, instead of connecting an exhaust vent pipe. The cap will prevent any debris that might be in the environment from entering the unit and causing damage or a fire hazard, as well as preventing rain or other weather from entering the unit. |
 |
|
Price: $59.00 |
Shipping:
$9.00 |
Total:
$68.00 |
|
|
| |
TK-TV13
Direct Vent Terminator |
|
The terminator can be used where a T-KJR is going to be vented out through a wall.
This is a CSA tested Takagi's component. Connect the Category III stainless steel vent pipe from the top of the unit to the backside of this terminator to exhaust flue gases through the wall without a thimble. Install this vent terminator in accordance with Takagi's installation instuctions and any applicable local codes. |
 |
|
Price: $119.00 |
Shipping:
$12.00 |
Total:
$131.00 |
|
|
| |
| |
TK-RE02
Temperature Remote Controller |
|
The TK-RE02 has two functions. It allows the output temperature from the TK-JR to be adjusted within the range of 99°F to 182°F, and it also works as a diagnostic tool that will give a concise error code whenever there is a problem with the unit. The temperature options are 99°F, 100°F, 102°F, 104°F, 106°F, 108°F, 109°F, 111°F, 113°F, 115°F, 117°F, 122°F, 131°F, 140°F, 158°F, and 167°F or 182°F. |
 |
|
Price: $149.00 |
Shipping:
$9.00 |
Total:
$158.00 |
|
|
| TK-BFO1
Exhaust Backflow Prevention Kit |
|
The TK-BFO1 Vent Damper prevents the backflow of air through the exhaust vent. This is a CSA tested Takagi component. This helps prevent harmful exhaust gases from entering the home, as well as helping to prevent the unit from freezing in areas where cold air can be blown or drawn into the exhaust system. Install this vent damper in accordance with Takagi's installation instructions, and any applicable codes. |
 |
|
Price: $49.00 |
Shipping:
$9.00 |
Total:
$58.00 |
|
|
| TK-TV09
Direct Venting Kit |
|
This kit can be used convert the TK-JR from a conventional vent system to a direct vent (or sealed combustion) system. This is a CSA tested conversion kit. Install this conversion kit in accordance with Takagi's installation instructions and any applicable codes. |
 |
|
Price: $59.00 |
Shipping:
$10.00 |
Total:
$69.00 |
|
|
| |
